![How to Finish Bias Binding in the Round How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/huge-529x651.jpg)
How to Finish Bias Binding in the Round
When using a bias tape to finish a garment, you will have to connect the two ends if you are finishing something in the round, such as an armhole, a cuff, or a bottom hem.
A common way to connect the two ends is at an angle. The advantage of this method is that you can reduce bulk at this connection point. It is especially useful if you are binding a thick fabric. One disadvantage I can think of is that the connection seam will be a bit more conspicuous, but really, I don’t think it’s such a big problem. I would, however, still position this connection seam in a spot that is not front and center of the garment if possible. Also, I would position it away from other seams on the garment so you don’t have a seam on a seam to minimize bulk.
Let’s get into the tutorial!
Here I have a piece of bias tape wrapping around the bottom of my sleeve. See that I am putting the right side of the bias binding to the WRONG side of the sleeve. Depending on your pattern, this may or may not be true, but I think it’s a very good method. I have also pressed in the seam allowance at the top long edge of the bias binding.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0489.jpeg)
Fold one end of the bias tape up at a 45-degree angle and finger press a crease (it’s much easier if you choose a fabric that can result in a sharp crease when pressed. This means a natural fabric, such as cotton, would be much easier than a synthetic fabric, such as nylon).
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0490.jpeg)
Similarly, fold the other end of the bias tape down at a 45-degree angle. Note that the diagonal folds are now butted against each other. Also, note that the bias tape should not have any slack—it should be the same length as the circumference of the hem.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0492.jpeg)
Now with the right sides together, overlap the creases and pin in place. As for the other pins that were on the sleeve, you can remove a few of them to make it easier to maneuver. I use my chalk to draw on the crease so it’s easier for me to see. Note that I unfold the seam allowance on the bias tape that I pressed earlier.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0493.jpeg)
Stitch on the crease through both layers of the bias tape.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0494.jpeg)
Now I can cut off the excess bias tape and press the seam open. I leave about 1/4″ (6 mm) of seam allowance on each side of the seam.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0495.jpeg)
I also re-fold the top seam allowance.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0496.jpeg)
Stitch the bias tape to the sleeve hem all the way around.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0497.jpeg)
Press the bias tape toward the seam allowances, and continue to wrap it over the edge. Place the fold on the bias tape to slightly cover the stitch line. Note that in this photo, I already turned the sleeve right side out.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0498.jpeg)
Now edgestitch along the fold all the way around. Yes, I edgestitch very close to the fold. I’d say about 1/16″ (1.6 mm). But if you have to stitch 1/8″ (3 mm), I think it’s perfectly fine.
![How to Finish Bias Binding in the Round](https://itch-to-stitch.com/wp-content/uploads/2021/02/IMG_0499.jpeg)
There you have it! That’s how you finish bias binding in the round!
Definitely going to give this a try. I need all the help I can get with bias binding finishing. Thanks for the tutorial 💕🧵
I can’t wait to try this out! For years I have been applying bias edgings from the garment front, and never gave one thought to doing it the way you do. I guess its the way we were taught in the past that makes us sewers not always question why we do things the way we do Hahaha!